Professional Service Tools:

 

Cooling System Air Purging Tool, Part# 031956, $44.95 each

Low coolant levels can cause severe overheating, resulting in engine damage. Especially designed for the MGB 1977-1980 without a radiator cap. Solid Brass fittings with high pressure hose to prevent kinking. Also fits: TR-7 1975-1980, MG Midget 1500cc, MG Midget 1275cc

Air Purging Tool

Overdrive Drain Plug Spanner, Part# 031955, $56.95 each

In order to service the transmission fitted with the A-Type overdrive, it is necessary to remove the large brass or steel drain plug. It is often very difficult to remove since it seizes in the aluminum case. This tool is designed to engage on the six notches and provides proper leverage for safe removal and replacement.
Fits Austin Healey 3000 BN2-BJ8, Triumph TR-3B-4A & TR-250-6
 

Overdrive Drain Plug Spanner Wrench

Rear Axle Hub Nut Wrench, Part# 031953, $45.95 each

Designed to fit either the original style hub nut or the later style currently being supplied by most British Car parts suppliers. Made from 3/8" thick solid steel. Fits Bugeye, Sprite & Midget. Use with any 1/2 drive ratchet wrench. Instructions included.

Rear Axle Hub Nut Wrench

Steering Wheel Puller, Part# 031941, $45.95 each

The factory never provided a means to remove the steering wheel on 1977-1980 MGB's. The all rubber steering wheel on these models must be removed in order to change the turn signal assembly or to upgrade to a performance wheel. Instructions included.

MGB Steering Wheel Puller

MGB Axle Hub Puller, Banjo Type Axle
Part# 031952, $45.95 each

Fits MGB, MGA. In order to replace leaking rear axle seals, it is necessary to remove the rear hub assembly. The threaded end of the axle housing is easily damaged if extra care is not taken during removal of the hub. This tool will quickly remove the hub without damage to the threads, bearing or hub. Instructions included.

MGB Axle Hub Puller, Banjo Type Axle

Rear Axle Hub Puller, Sprite, Part# 031951, $45.95 each

Fits Sprite, Midget, Bugeye. In order to replace leaking rear axle seals on the above models, it is necessary to remove the rear hub assembly. The threaded end of the axle housing is easily damaged if extra care is not taken during removal of the hub. This tool will quickly remove the hub without damage to the threads, bearing or hub. Instructions included.

Rear Axle Hub Puller, Sprite

Grease Cup Puller, Part# 031943, $43.95 each

Pulling the front grease cups can be very frustrating when servicing the many WIRE WHEEL models.  Grease cups must be removed to pack wheel bearings, replacing front seals, rotors or performing front end rebuilds.  Shop quality service tool. Instructions included.

Grease Cup Puller

Rear Axle Puller, Tube Type, Part# 031944, $29.95 each

Used for MGB & MGBGT's rear axle service work. Axles must be removed in order to change wheel bearings, 3rd member front pinion bearing or thrust washers to eliminate that clunk-clunk sound. Instructions included.

Rear Axle Puller, Tube Type

Window Seal Clip Tool, Part# 031948, $28.95 each

Triumph, Sprite & Midget door glass outer rubber seal and inner fuzzy seals utilize clips to hold them in place.  This can be a very frustrating job.  During routine replacement or during restoration this handy tool magnetically holds the clip in place on the tool to facilitate installation. Shop quality tool.  Instructions included.

Window Seal Clip Tool


"Strive for perfection in everything. Take the best and make it better. If it doesn't exist, create it.
Accept nothing nearly right or good enough."  
Sir Henry Royce, co-founder Rolls Royce
 

 

1602 W Shields Ave, Fresno, CA 93705-3347
Email:  britstuph@gmail.com
  Phone (559) 221-7971